surface contact

Finite element analysis of multi-asperity surface contact under normal distribution pressure

多微凸体粗糙面接触的有限元分析

Integrated die drawing to produce multi-wire composite structure surface contact wire rope

整体模拉法生产多丝复合结构面接触钢丝绳

Study on surface contact stress and settlement properties during dynamic consolidation

强夯的边界接触应力与沉降特性研究

The surface contact angles were measured with high temperature microscope .

利用高温显微镜测定两种材料的表面接触角；

The Research on Surface Contact and Wear of Overhead Transmission Wires

架空输电导线的表面接触与磨损机理研究

Study on surface contact stress distribution properties for multi-layered foundation during dynamic consolidation

强夯作用下成层地基的表面接触应力分布特征

Surface Contact Fatigue Failure Analysis on the Cam of CNG Engine

CNG发动机凸轮表面接触疲劳失效分析

The Effect of Surface Contact Conductance on The Strip Exit Temperature

界面接触热导对铸坯出口温度的影响

A research for influence of the gear pressure angle on tooth surface contact intensity

轮齿压力角对齿面接触强度的影响分析

Simulate friction contact problem between piles and soil with surface contact element .

用面面接触单位模拟桩与土体的摩擦接触问题。

The results show that metal surface contact resistance decreases with the increment of pressure .

研究表明：材料的表面接触电阻是压强的函数。

The surface contact angle , water content and oil absorption of the particles were measured .

根据改性前后SiO2表面的接触角、含水率、吸油值的测定结果，表明复合改性后SiO2的憎水性和亲油性得到改善；

The results of burned hole with optical fiber are better than those with surface contact .

激光光纤烧洞后碎石比表面接触碎石效果更好。

The concept of band osculation is presented by analyzing surface contact types .

通过对曲面接触类型分析，提出了带状密切的概念。

Using surface contact model between stator and rotor , the pressure equalizing operation is realized .

采用定转子面接触模型，实现了电机的均压运行。

Influence of rolling contact fatigue loads on stress intensity coefficients of rail surface contact fatigue crack

滚动接触疲劳载荷对铁轨表面接触疲劳裂纹应力强度系数的影响

Discusses thoroughly the phenomena of wear mechanisms , surface contact stresses , and surface fatigue .

深入探讨机械磨损机理、表面接触应力和表面疲劳现象。

Surface contact and tight fit of supporter were calculated by traditionally mechanic theory .

按按传统力学理论对托轮的表面接触应力和过盈配合进行了计算；

Master surface-slave surface contact model is used to define the contact between tools and blank .

用主从面（mastersurface-slavesurface）模型定义板料和模具的接触，摩擦力用库仑定律计算；

Bacterial density , surface contact and physiological signals are stimulating factors of swarming motility .

菌细胞密度、表面接触和生理学信号均可成为群集运动的刺激因素。

Surface Contact Disinfecting Technology

表面接触消毒技术

The introduction of PEG decreased the surface contact angle and the bacteria adhesion on polymer surfaces .

引入PEG不同程度地降低了材料表面的接触角，减少了细菌在共聚物表面的黏附；

Mises stress in surface contact center of coating system is not equal to zero , which is different without coating .

与无涂层的情况不同，涂层体系表面接触中心处的Mises应力不为零；

Sensors detect changes in tilt of the body , longitudinal and transverse acceleration , as well as road surface contact .

传感器可检测车身倾斜度、纵向和横向加速度以及路面接触的变化情况。

It changes the instantaneous contact status between grinding wheel and cam and leads to instantaneous surface contact / non-contact .

带预紧硅泡沫垫层结构接触状态的有限元分析③改变砂轮与工件的瞬时接触状态，出现瞬时飘空、瞬时面接触；

The mechanics characters of friction drive mechanism , surface contact characters and some the relations between frictions drive and precision orientation is analyzed .

分析了摩擦传动机构的力学特性，对摩擦表面接触的特性进行了分析，并对摩擦传动在精密定位方面的相关问题进行了研究。

Some performance indexes such as surface contact angle , molecular weight , crosslinkage , tensile strength and break elongation etc. were investigated .

对EB辐照薄膜的某些性能指标，如表面接触角、分子量、交联度及拉伸强度、断裂伸长率等进行了测试。

Then study on the relationship between surface contact angle and different plasma treating factors including treat time , treat voltage and coated amount of simethicone .

其次研究了不同等离子体处理因素包括等离子体处理时间、等离子体处理电压和二甲基硅油涂覆量与表面接触角之间的关系。

Contact temperature is one important working proprieties of friction pairs , there are no study on the contact temperature fields of rough surface contact at present .

接触温度是评价摩擦副工作性能好坏的一个重要因素，对粗糙表面、特别是含磨屑粗糙表面接触温度场求解尚缺乏深入研究。

The performance of the sized paper tested were : dry or wet ring crush , tensile strength ( breaking length ), surface contact angle .

将表面施胶后的纸样再进行进一步的性能测试：包括干、湿环压强度，抗张强度（裂断长），表面接触角。